Lesezeit ca. 8 Min.


Logo von Inch
Inch - epaper ⋅ Ausgabe 1/2020 vom 10.03.2020

Antoni Gaudí’s masterpiece, the Sagrada Família church in Barcelona, has been under construction for nearly 140 years, but only 60 percent of the structure had been built by 2014. Now, using modern engineering and construction techniques the remaining 40 percent is due to be completed by 2026, the centenary of Gaudí’s death. Tristram Carfrae RDI FREng, deputy chairman of Arup, explained to Hugh Ferguson how this is being achieved without compromising Gaudí’s vision or quality standards.

Artikelbild für den Artikel "ARCHITECTURE: COMPLETING THE SAGRADA FAMÍLIA" aus der Ausgabe 1/2020 von Inch. Dieses epaper sofort kaufen oder online lesen mit der Zeitschriften-Flatrate United Kiosk NEWS.

Bildquelle: Inch, Ausgabe 1/2020

An Antoni Gaudís Meisterwerk, der Basilika Sagrada Família in Barcelona, wird seit nahezu 140 Jahren gebaut ...

epaper-Einzelheft 9,99€
NEWS Jetzt gratis testen
Bereits gekauft?Anmelden & Lesen
Leseprobe: Abdruck mit freundlicher Genehmigung von Inch. Alle Rechte vorbehalten.
Lesen Sie jetzt diesen Artikel und viele weitere spannende Reportagen, Interviews, Hintergrundberichte, Kommentare und mehr aus über 1050 Magazinen und Zeitungen. Mit der Zeitschriften-Flatrate NEWS von United Kiosk können Sie nicht nur in den aktuellen Ausgaben, sondern auch in Sonderheften und im umfassenden Archiv der Titel stöbern und nach Ihren Themen und Interessensgebieten suchen. Neben der großen Auswahl und dem einfachen Zugriff auf das aktuelle Wissen der Welt profitieren Sie unter anderem von diesen fünf Vorteilen:

  • Schwerpunkt auf deutschsprachige Magazine
  • Papier sparen & Umwelt schonen
  • Nur bei uns: Leselisten (wie Playlists)
  • Zertifizierte Sicherheit
  • Freundlicher Service
Erfahren Sie hier mehr über United Kiosk NEWS.

Mehr aus dieser Ausgabe

Titelbild der Ausgabe 1/2020 von TECH CLIPS. Zeitschriften als Abo oder epaper bei United Kiosk online kaufen.
Titelbild der Ausgabe 1/2020 von WIND ENERGY: KITE POWER. Zeitschriften als Abo oder epaper bei United Kiosk online kaufen.
Mehr Lesetipps
Blättern im Magazin
Vorheriger Artikel
Nächster Artikel
Mehr Lesetipps

... und doch waren 2014 nur 60 Prozent des Baukörpers komplett. Mit modernen Konstruktionsmethoden sollen nun die restlichen 40 Prozent bis 2026, hundert Jahre nach Gaudís Tod, fertig gestellt werden. Tristram Carfrae, stellvertretender Vorsitzender von Arup, erklärte Autor Hugh Ferguson, wie so eine Aufgabe bewältigt werden kann, ohne Gaudís Vision und Qualitätsstandards zu verletzen.


Arup was called in to collaborate with the Sagrada Família Foundation and its well-established team of in-house architects and builders in 2014, initially with one particular challenge: one of the 18 towers - the Mary Tower over the crypt - was going to weigh too much for the foundations installed in 1877, and some fresh ideas were needed. How could a tower be designed and built that would work both structurally and visually while following the guidelines that Gaudí had set and maintaining the highest quality? An earlier idea had been to erect an interior steel structure on which stonework could be hung, but this was seen as inappropriate.

Meanwhile other factors were at work. The trickle of donations to fund construction had turned into a torrent, as Barcelona’s booming tourist industry brought more paying visitors, particularly after the completion of the nave and consecration of the church by Pope Benedict in 2010 - there are currently some four million visitors per year. A major constraint on the speed of construction had been removed, and the bold decision had been taken to complete the structure, but not necessarily the decoration, by 2026. This required a tenfold increase in the speed of construction compared to the previous 130 years.

Another element to consider was that traditionally all construction work for the church had been done on the site, which was becoming cramped as the building expanded. It was also becoming unmanageable, as the pace of construction, and hence the workload, increased, and the church was still having to remain open for its many visitors. The case for off-site fabrication was strong.


The first action was to determine the shape of the tower. No models or drawings of the Mary Tower survived, so a design had to be recreated from fragmentary archival evidence and by extrapolating from Gaudí’s use of geometry in his model for the sacristy. A series of hyperbolic paraboloids were rotated about a central axis and intersected. This was then modelled in 3D software and elongated to create a tower with a scalloped multi-sided shape in plan, with many small triangular windows, shaped as hyperboloids.

Next a structural form was needed. Various ideas were conceived, modelled and then tested by finite element analysis to reveal the stress levels in each element under different loading conditions. Earthquake loading was important, but in most cases the critical condition was under extreme wind loading. Each idea was tested at various levels of computer analysis, starting with the ‘quick and dirty’ and moving swiftly to the highly detailed.

As a start, Arup modelled what would happen if the tower was built in traditional stone masonry - thin enough to be within the weight that could be carried by the foundations. Under normal loading the tower behaved reasonably well but under extreme wind loads all parts of the masonry facing the wind went into tension. As traditional masonry is very strong in compression but very weak in tension this approach would not work.

Building the church's tower with pre-formed, pre-stressed panels instead of traditional masonry reduced the weight of the tower and allowed for fast, off-site construction.

mock-ups produced by the Foundation, to check appearance, and for ‘buildability’. Every detail was carefully planned, and a kit of parts assembled including the stainless steel rods and bolts for the pre-stressing. Careful design of connections combined with precise manufacture ensured that the panels when craned into position could fit together like Lego blocks, with no on-site adjustment.

After further modelling a potential solution was proposed. Instead of using traditional construction, what if the masonry was pre-formed in larger panels and pre-stressed using tensioned steel rods before erection? In this way, the masonry could be pre-compressed so that it would be much less likely to go into tension under wind loading. Panels around 4 metres high by 3 metres wide, 14 to a ring of the Mary Tower and weighing around 5 tonnes each would suit the geometry and be reasonably easy to create and erect. The panels could then be simply bolted together, with shear connectors on the horizontal joints.

Finite element analyses demonstrated that this strategy could work. Under extreme wind loading, almost all elements of the panels remained in compression, though there were some elements that could move into tension, which could then lead to a crack forming in the masonry. The question then was whether the crack would open up with serious consequences or whether the loads would redistribute safely in the remaining structure: a simple re-run of the analysis removing the element in tension confirmed the latter.

The pre-stressed masonry panels had the additional advantages that they retained the use of Gaudí’s preferred sandstone as the primary structural material, they were ideally suited to off-site construction, and they achieved the necessary weight reduction: the stone in the panels is just 300 millimetres thick, compared with around 1.2 metres for traditional masonry, and resulted in a structure just light enough for the foundations.

Once the overall form was determined, the team modelled every component of each panel to a construction level of detail, including nuts, thread bars, couplers, fillets and chamfers. In this they were assisted by full-scale mock-ups produced by the Foundation, to check appearance, and for ‘buildability’. Every detail was carefully planned, and a kit of parts assembled including the stainless steel rods and bolts for the pre-stressing. Careful design of connections combined with precise manufacture ensured that the panels when craned into position could fit together like Lego blocks, with no on-site adjustment.


Antoni Gaudí (1852-1926) was in his early thirties when he took over as architect for the Sagrada Família, before his modernist buildings in Barcelona had established his reputation. His appointment followed the resignation in 1883 of his predecessor, with the stone crypt of a neo-Gothic church already nearly complete.

Gaudí spent the next 43 years developing his own distinctive design for a far larger and different structure, in his later years working exclusively and obsessively on the church, driven by his profound Catholic faith. He never expected the church to be completed in his lifetime, and as he once famously observed: “My client is not in a hurry”. Besides, construction was funded by private donations and could proceed no faster than the flow of money.

But he left plenty of clues as to how it should be finished. He completed the crypt, the façade of the apse and just one of the planned 18 towers, plus much of the Nativity entrance - which served as examples. He also left extensive drawings and plaster models.

An explosion during the Spanish Civil War destroyed or extensively damaged many of the drawings and models, though much has been recovered by painstaking restoration. Where models exist, the current design team follow them exactly. Where only drawings or fragments of models remain, the team uses a degree of interpretation, complicated by the changes in Gaudí’s thinking and drawings during his lifetime. Where there is no evidence, they can freely interpret his intentions.

At the time of Gaudí's death in 1926, only the Nativity façade and a single spire had been completed, 75 percent of the construction was unfinished (Photo from 1929).

In the last 100 years construction methods have changed - and speeded up. The completion of the Sagrada Familia is expected in 2026, the centenary of Gaudí's death.



The interior of the Sagrada Familía is as breathtaking as the exterior. Gaudí's organic style is omnipresent.


Meanwhile a suitable fabrication site was found north of Barcelona, some 90 minutes from the church. Here the digital model was used to automatically cut the stone, with its angled jointed surfaces finished to within one millimetre by computer-controlled cutting. A more traditional method was used to match the rest of the church with the outer finish of naturally broken sandstone: the edges were hit very hard with a sledgehammer.

Then the individual stone blocks were fabricated into a panel using laser-cut plywood templates, and pre-stressed with machined duplex stainless steel bars, inserted through holes predrilled through the masonry. Finally the holes were grouted, to provide further long-term protection to the steel rods.

In this way a production line was formed. Each of the 14 panels in a ring was identical, so there was helpful repetition, but as the tower is tapering, each successive ring was smaller as the tower rose. It took a month to fabricate each ring, but then only a day to assemble it on site: the care taken in design and the accuracy of manufacture meant that the panels slotted together rapidly with a minimum of fuss, so minimising both the use of limited crane access at the church and disturbance to church activities and its visitors.

The principle of pre-stressing masonry panels and the off-site production method have been adopted for construction of the remaining towers, in particular, the tallest of all, the mighty Jesus Tower that sits above the crossing of the nave. Before Arup’s arrival, the plan had been to build the tower in reinforced concrete and clad it in stone. But experience with the Mary Tower demonstrated that pre-stressed masonry panels would not only be more appropriate, but also easier and faster to build.

Construction started in July 2019 and the process has been identical to the Mary Tower except on a larger scale: the masonry thickness is 450 millimetres instead of 300 millimetres, there are 12 panels per ring instead of eight and each panel weighs 25 tonnes instead of 5 tonnes. When the Jesus Tower is ‘topped off’ with its five-armed cross, the Sagrada Família will at 172.5 metres be the world’s tallest church and Barcelona’s tallest building.

Inside the Jesus Tower a lift and staircase will carry visitors up into the cross. The spiral stone staircase will be cantilevered from the inside of the stone-panel wall, following a long tradition in masonry architecture. In this case, there is the added complication that the staircase has to span some of the openings in the tower: the solution, again, is to post-tension the stone to allow the staircase to bridge the gaps. The lift shaft will then be assembled up the middle of the tower.

Tristram Carfrae is well used to working closely with architects and builders worldwide, but never before has he experienced such close collaboration - due in part to the long-established in-house architect/builder team and in part to the simple, shared objective: to build the best church in the world. “It just makes me inordinately happy, and fulfilled, and pleased that I became a structural engineer to get to work on things like this.”

Hugh Ferguson

Dieser Beitrag ist ursprünglich in Ingenia, Ausgabe 81 vom Dezember 2019, erschienen. Die Veröffentlichung erfolgt mit freundlicher Genehmigung der Royal Academy of Engineering. Der Originalbeitrag findet sich unter www.ingenia.org.uk/getattachment/Ingenia/Issue-81/La-Sagrada-Familia/La-Sagrada-Familia.pdf

https://sagradafamilia.org Offizielle Webseite der Sagrada Família mit vielen Informationen.

www.arup.com/sagrada-familia Projektseite von Arup zur Sagrada Família.

Links, Vokabeln & mehr unter www.inchbyinch.de/inch24/sagradafamilia